6.6kW Bi-Directional On-Board Charger with 2.5kW DC/DC Converter

Price:

£ 1,198.98


Safety Disconnect - Fuse MSD
Safety Disconnect - Fuse MSD
£ 57.75
£ 57.75
150kW 3-in-1 Coaxial Rear E-Axle Kit
150kW 3-in-1 Coaxial Rear E-Axle Kit
£ 6,989.99
£ 6,989.99

6.6kW Bi-Directional On-Board Charger with 2.5kW DC/DC Converter

https://shop.fellten.com/web/image/product.template/24161/image_1920?unique=e1d5e79

£ 1,198.98 1198.98 GBP £ 1,198.98

£ 1,198.98

Not Available For Sale


This combination does not exist.


Share :
Terms and Conditions

Orders Dispatched Within 24 hours  - Excluding Weekends and Bank Holidays.

Worldwide Shipping
30 Days Return
Fast Delivery


A 6.6 kW bi-directional onboard charger and a 2.5 kW DC/DC converter in one liquid cooled, IP67 sealed housing. It charges a 200 to 500 V pack from a single phase supply, keeps the 12 V system topped up, and can run in reverse to supply 3.3 kW of AC power from the traction battery.

Combining the charger and DC/DC converter saves a box, a set of high voltage cables and a cooling loop in a conversion. The DC/DC delivers 2.5 kW continuously, with 3 kW available for six minutes, which covers the lights, pumps, fans and heated screens of most road vehicles. The inverter mode turns the vehicle into a power source for tools, a campsite or a backup supply. It shares one coolant loop with the rest of the drivetrain, is rated from minus 40 to plus 85 degrees, and talks to the BMS and VCU over CAN.

Key specifications

Manufacturer partTCCDB66662252
TypeBi-directional onboard charger with integrated DC/DC converter, liquid cooled
AC input90 V to 264 V, 45 Hz to 65 Hz, up to 32 A
Charger output voltage range200 V to 500 V
Charger rated output6.6 kW, 22 A at 350 V
Charging efficiency94 percent or better at rated voltage and full load
Power factor0.98 or better above half load, 0.99 or better at full load
Inverter output (V2L)3.3 kW, 220 V 50 Hz as standard, 220 V 60 Hz or 110 V 60 Hz available by firmware
Inverter efficiency92 percent or better
DC/DC input200 V to 500 V from the traction pack
DC/DC output9 V to 16 V, 14 V nominal, 172 A rated, M8 stud terminal
DC/DC power2.5 kW continuous, 3 kW peak for 6 minutes
DC/DC efficiency91 percent or better, weighted
CommunicationCAN bus at 500 kbps, default charger ID 0x1806E5F4, alternative IDs available
ProtectionInput and output over and under voltage, short circuit, overcurrent, overtemperature, DC/DC input reverse polarity
CoolingLiquid, 6 to 8 L/min, coolant inlet up to 65 °C, under 100 mbar pressure drop at 8 L/min
Ingress protectionIP67
Operating temperatureMinus 40 to plus 85 degrees C
Storage temperatureMinus 40 to plus 95 degrees C
Dimensions322 x 247 x 69.5 mm
Net weight6.5 kg
DocumentationDatasheet and installation drawing in the Documents tab

Features

  • Charger, DC/DC and inverter in one unit, so there is one box to mount, cool and wire instead of two or three
  • 6.6 kW fills a typical conversion pack overnight from an ordinary single phase supply
  • Wide 200 to 500 V output window suits most modern high voltage packs through their whole state of charge
  • 3.3 kW vehicle to load output runs tools and equipment straight from the traction battery
  • Inverter output set by firmware for 50 Hz or 60 Hz markets, including 110 V for North America, and the unit can be reflashed later
  • 2.5 kW DC/DC with a 3 kW short term peak, enough for a full 12 V vehicle electrical load
  • Liquid cooled and IP67 sealed, so it can be mounted outside a dry enclosure and share the drivetrain coolant loop
  • Controlled over CAN, so the pack governs the charge rather than the charger following a fixed curve

Connectors

The unit uses automotive sealed connectors throughout, and the mating halves are supplied with it. Part numbers, if you need spares:

AC inputAmphenol HVC4P63MV106-S02
HV DC (charger output and DC/DC input)TE 2367138-1
Signal and controlMolex 643340100, with CAN, wake up, CP, CC, charge lock control and temperature sensor inputs
12 V outputM8 stud, tighten to 14 to 18 Nm

Firmware options

The AC output and CAN ID are set in firmware. Units ship as standard with 220 V 50 Hz output and charger ID 0x1806E5F4. Tell us when you order if you need a different version, or we can supply the file to reflash a unit you already have.

Standard220 V, 50 Hz output, CAN ID 0x1806E5F4
9910-006.01220 V, 60 Hz output, CAN ID 0x1806E5F4
9910-005.01110 V, 60 Hz output, CAN ID 0x1806E5F4
9910-008.01220 V, 50 Hz output, CAN ID 0x1806E7F4
9910-007.01220 V, 50 Hz output, CAN ID 0x1806E8F4

The alternative CAN IDs let two units share one bus, or avoid a clash with another device already using the standard ID.

In the box

1 x TCCDB66662252 bi-directional charger and DC/DC converter
1 x set of mating connectors for the AC input, HV DC and signal ports

Cable, coolant hoses and mounting hardware are not included.

Downloads

The datasheet, installation drawing and a STEP model are all in the Documents tab above. The installation drawing shows mounting points, connector positions and coolant ports. The 3D model on this page is the same geometry.

6.6kw+2.5kw_bi-directional_TCKH-1485BW_A (1).pdf
Download
bicharger-1080p-av1.mp4
Download
CD-S T1.stp
Download
3D model

Drag to rotate. Use the buttons to zoom, or pinch on a touch screen.